Do I need to break in my speakers or subwoofer(s)? Username: Nickadam55 Columbia MO, Missouri Post Number: 92 Registered: Feb-09: Posted on Thursday, February 18, 2010 - 05:51 GMT . With this, you shall be assured to have a high-quality sound on your music. Setting the gain control sets the level of distortion in your tone, regardless of how loud the final volume is set. Have a thought on the dislikes of the tone produces as well as what you like about it. When playing the guitar chords and striking them hard, note whether there is a tone piercing to the ear. The basic controls in the guitar amps include; These basic controls will be in almost all guitar amps and, therefore, you will most likely to interact with each one of them. This can be observed if you do an experiment with different guitar amps but use completely same settings; a different tone will be produced. This music is very similar to the metal music and they will share a lot of guitar amp settings. External car audio amplifiers have the potential to vastly improve the performance of a vehicle's speakers. Nick Adams. This is likely to guide you towards the music you ever had a thought of. By the use of the higher strings with your guitar at 10, play it and determine whether there are any distortions or if the sound seem to be thin. You will either love the result or you will be frustrated with the settings made on the amp. Avoid channels that might lead to distortion not based on the settings made. CD or file with a sine-wave test tone recorded at 0dB reference level in the frequency range to be amplified (for example: 50 Hz for subwoofer channels, 1 kHz for a midrange application). The following are discussions on different settings of various types of music. This will necessitate various adjustments to the guitar amp settings which will include the following; The rock music can use both the humbucking and single-coil pickups as compared to the metal which requires only humbucking to give the quality tone. Turn the input sensitivity control on the amplifier all the way down. If the bass distorts the tone, then turn the bass knob down to the point where it is clear. You should just use RCA to RCA and you will be fine if the amp in fact has a gain of 29 dB. It means that it adjusts the power from the amplifier to the level, where it can be managed easily by the speakers. The rock guitarists will use their guitar amps with low volume. After the above settings have been done, pick the guitar and play the E major chord then followed by the G Barre Chord and note the tone produced. Turn off all processing on the source unit and the amplifier (bass/treble, loudness, EQ, etc.). Before you decide on the settings for the music to play, ensure that you first produce a clean tone from the basic settings on the amp. Or have you purchase a guitar amp and need some guidance on the settings? This is accomplished by listening to the system at a moderate level and turning down the input sensitivity controls of amplifiers that are playing too loudly. The basic results include; With these three results from your guitar amp settings, you will have in your metal tone in which you can then customize them to have the tone in line with your preferences. Rock music is one of the best music tones loved by most people. NEED AMP GAIN SETTING CHART . They include Boss ST-2 Power Stack, Boss ML-2 Metal Core, and Boss MD-2 Meta Distortion. Disconnect the speaker(s) from the amplifier. Certain after-market component and direct-fit factory replacement speakers may require the use of an external amplifier, due to the power requirements of the speakers used in the sound system. Do not use attenuated test tones (–10dB, –20dB, etc.). This will ensure that you have the best experience while setting your guitar amp as well as through playing this metal music. Make sure to measure the voltage at the correct connectors (+ and -). Follow these specific guitar amp settings on your metal music to get the clear instructions. This will allow for reasonable gain overlap with moderate clipping at full volume. On the channel also ensure that there are no overdrive buttons that are pushed in to give you a fresh start. Some people have very sharp musical hears and they will automatically get bored by the bad settings which lead to poor quality sound. On addition of some effects, there will need to make some changes such as when you start using a guitar pedal you might need to adjust the gain knob. Music is one of the things which become very critical in the settings made. With this guide, you will be able to get the best tone using your musical ear and getting the best tone you would love yourself. Before any adjustment, therefore, there will need to think critically about what changes to make rather than tweaking the knobs randomly. or an easy formula? Do not increase the input sensitivity of any amplifier as this will defeat the purpose of this procedure by permitting excessive clipping (distortion). Now let us discuss the various ways to set your amp for the metal music. The pedals will always contain equalizer that can be used in place of guitar amp setting through replacing the gain knob. If you meant the AVR was set for 4 Ohm speakers, @everettT suggested you change it back to the default setting of 8 Ohms, if I understood his post#79 correctly. This, therefore, necessitates the use of the guitar amp setting guide.