The benefit of the Push Pull is that you can simply engage the Series sound whenever you want – like a “fat switch”. Richmond VA 23227 | (804) 358-2699 | Thanks. It sounds a lot like a faulty switch or sweeper. How do you make such terrific drawings? Each manufacturer can be slightly different. The signal experiences more resistance, thus getting bigger and beefier as a result. This is our favorite schematic and function. It should be possible, but the switching will be different. Bodies take USA sized parts and are FULL thickness 43-45mm deep. With over 80 shape and thickness combinations, plus a choice of time tested tone woods, USACG necks are truly custom pieces, made for individual players’ preferences. All the rod's inward compression is absorbed by rod itself. Fender American Professional Stratocaster Neck, 22-Fret. Mighty Mite does not supply these bushings. If you haven’t already, check out the rest of 4-way switch wiring diagrams on the internet. The Iolana lap-steel, manufactured by Valco in the 50’s, was a double-neck affair with a reverse-headstock on the lower of the two necks to improve tuner access. Do you know what type of switch it is? That’s what I prefer. I’ve gone over it so many times that my eyes are crossing. If you didn’t want to do anything with the 3rd Conductor, simply tape it off with some masking tape. Thanks for the love. I have a bit of the opposite problem. The first production 6-string electric guitar to feature a reverse headstock – on a neck-through design no less – was the Gibson Firebird®, which was released 1963. The frets didn’t need to be touched to be low action and buzz free. The pot lets you mix the amount of “other” pickup you want, so it doubles as a “capless” tone control. I love that fourth position. I’d just have to solder the jack wires and pickup wires onto it? It’s a simple mod that when added to your Telecaster, puts your pickups in Series, instead of Parallel. Follow up. If the neck pup is from a strat is there an issue with not having a cover. With Parallel wiring, the perceived sound decreases when combined with another pickup. You can find Fender’s original diagram all over the web, even though the switches are the same. Odd… I have to be dong something wrong if it works for everyone else. 7 available from $549.99. Tried the switch on several teles and several wirings. The slot on the control plate for the blade switch was not long enough for the blade switch to reach position 1. Just to make sure, since I’ve seen the switch settings can be different per vendor online, you wire the switch so that position 3 is the Bridge/Neck in Series, and position 4 is the Neck by itself, correct? The switching is not working for me. You should be able to find a diagram somewhere online for this. However, on a typical Strat or Tele pickup, there are anywhere between 80-100 turns of coil on the initial pass. This wiring is for the Oak Grisgsby 4-Way Switch. Do I understand you’re a Virginia guy? Also, it comes pre-soldered, correct? I bought a custom 4-way 920D built control plate. 4.5 out of 5 stars 66. To see how this mod is performed, check out our guide here: Convert your Tele Neck into a 3-Wire Neck 2020 Fender Player Jaguar NECK 9.5" … Thanks, Tyler, I found that using both black and shield from the Peavey “humbucker” Tele pickup on a pot ground gave me a satisfactory solution, not perfect. Any reason I’d have to tell you it’s for a lefty tele? But I can’t decide whether to go for a 4-way switch or a push/pull tone pot switch. Convert your Tele Neck into a 3-Wire Neck, Convert Your Tele Neck Into a 3-Wire Neck, https://www.youtube.com/watch?v=VipIfXFjnXM. I am building my tele with a p90 in the neck, and a normal bridge, and this is my first build, will the four way still work with the p90?